158 products were found matching your search for backup in 1 shops:

The EX-3455 SATA 2 hardware RAID controller was designed to easily upgrade yournew or existing system with RAID 1 or 0 hardware. The installation is very simple. Both hard drives and a port of the motherboard areconnected to the EX-3455. For an existing operating system, data from hard drive 0 is automatically copied to hard drive 1 in the background. You can continue to work normally during this time. When a new operating system is installed,the data is written to both hard drives simultaneously with no loss of speed.The EX-3455 can be installed in an 8.9 cm (3 1/2'') or 13.34 cm (5 1/4'') front bay or in a PCI Expressslot. With the low-profile bracket, the EX-3455 can even be used in anarrow housing up to a height of 8 cm.Since the EX-3455 requires no drivers and software, it can be used for any operating system.• 1-to-2 SATA 2 hardware RAID 0/1 for two SATA 2 hard drives• Supports RAID 0, 1, LARGE and EZ-RAID 1 mode can be adjusted via DIPswitches• Supports RAID 1 with auto rebuild in the background• 3 1/2'' or 5 1/4'' front slot for normal or narrow computer systems• Supports hard drives over 2 TB• LED display for the RAID and hard drive status• Complete SATA 2 and power cable set, including standard and low-profile bracket• Suitable for all operating systemsSpecifications:• Data transfer rate: from 1.5 GB/s to 6.0 GB/s• Connections: 1 x 7-pin SATA connector from the motherboard• 2 x 7-pin SATA connector to the hard drives• 1 x power connection from the housing power supply unitHardware systems:• 3 1/2'' or 5 1/4'' housing slot or PCI Express slot• Operating temperature: 0 to 55 Celsius• Storage temperature: -40 to 75 Celsius• Relative humidity: 5% to 95%• Size: 74 x 68 mm• Weight: 400 gIncluded with delivery:• EX-3455, 3 x SATA 2 cables, 1 x power cable• 3 1/2'' or 5 1/4'' frame, standard and low-profile bracket• Manual

Personal Backup Hub BeeDriveThe repository of your personal dataBeeDrive is the central place for your data backup, allowing you to simplify the backup (backup & sync) of your important files and photos from your computer and smartphone. Once the device is connected, you can also effortlessly sychronize files and transfer them wirelessly from mobile devices to computers.Backup from PC & mobile devicesSet up once and sit backFile syncSyncs files when a device is connectedFast transfer ratesUSB 3.2 Gen 2 (Type C) with integrated SSDBeeDropTransfer files from mobile devices to PC via WLANDrop resistanceDrop protection up to 2 meters*PC backupTake advantage of BeeDrive's ultra-fast transfer rates and never worry about data protection concerns again, as with backups to public clouds. With PC backup, you can even back up selected folders automatically. All you need to do is set up the device once and the backup process will start automatically as soon as you connect BeeDrive.Folders can be backed up automatically in real timeKeep up to 5 file versions. So you can access previous versions in case of emergencyDeleted computer files are stored in the ''Archived Files'' folder for effortless recoveryFile synchronizationFile synchronization features are ideal for hybrid work models, automatically synchronizing recent changes between computers. This allows you to ensure consistent workflows wherever you are.Folders can be automatically synchronized when BeeDrive is connected to your computerKeep up to 5 file versions. So you can access previous versions in case of emergencyCustomize your sync settings to your personal needs with options for one-way or two-way syncBeeDrive for mobile devicesStore all your photos, free up phone storage, and save on rising cloud storage costs. Every time you connect BeeDrive to your computer after the initial setup, your photos are backed up automatically via Wi-Fi.With the BeeDrive mobile app, you can easily back up photos from up to 5 mobile devices.For best results, you can use concentrated backup to keep your app open in the foregroundUse options to backup HEIF or HEVC media as JPEG to ensure compatibility with non-Apple devicesPackage Contents:BeeDrive main unitUSB-C to -C cableAdapter for USB-C to -AQuick Start Guide

FMB920 Small and Smart Tracker with Bluetooth and Accelerometer1x Digital Input1x Digital Output1x Analog Input1x Micro USB 2.01x Micro SIM slot128 MB internal flash memoryWireless BandsGSMGPRSGNSSBluetoothFMB920 is a slim design easily fitted tracker with GNSS/GPS internal antennas, flash memory, integrated backup battery, accelerometer, inputs/output and various BLE 4.0 connectivity sensors and beacons support. Thanks to a rich feature set, this EASY category tracker delivers unquestionable value for the GPS telematics service providers and end-users.The model has been designed for light commercial vehicles and passenger cars tracking in:insurance telematicsrental and cars sharingrecovery of stolen carspublic safetycourier delivery servicestaxicorporate fleetsetc. The true bestseller FMB920 is compact, reliable,accurate, and affordable - the qualities appreciated by our clients throughout the world.

Synology C2 Backup 500 GBBrand new is now another physical license from Synology! The C2 Backup license. This is a cloud backup solution to the Synology C2 Cloud. The license allows 500GB backup to the C2 Cloud with a term of 1 year! Backup your data to your Windows PCs, Mac devices, and Microsoft OneDrive in the cloud so you never lose a file again.Max. Number of devices: UnlimitedEmail notifications possibleBackup the whole systemBack up your entire PC, including operating system, configurations, installed software and files.Incremental backupSave disk space by backing up only the data that has changed since the last backup.VersioningSelect the version you want to restore from several backed up versions.Backup scheduleScheduled on a daily/weekly basis or triggered by events (boot up, screen lock or log off).Bare metal restoreRestore your entire PC to a previous version of your system. Currently only available for Windows devices. Mac devices will be supported at a later date.File-level restoreRestore individual files or folders.PlatformsWindows 7 SP1Windows 10Windows 11macOS 10.15.7 and higherHow is my device backed up?Your entire PC is backed up to C2 backup servers, including operating system, installed applications, documents and media files. In case of emergency, you can either restore the whole system or download individual files or folders.Can I back up external devices?Yes. When configuring your backup policy, simply select ''Entire device'' as the backup method and make sure ''Back up external devices'' is selected.How long does the backup take?Since backup duration depends on available bandwidth, network traffic, and the number and size of files being backed up, it is not possible to accurately predict how long your backup will take. Please also note that a full backup is required the first time, while incremental backups are performed thereafter. As a guideline, backing up 500 GB of data for the first time can take up to 11 hours at an upload speed of 100 Mbps.

FMC225 Waterproof LTE Cat1 Terminal with RS232/RS485 interfaces and Backup Battery2x Digital Inputs1x Digital Output1x Analog Input1x CAN Adapter Input1x 1-wire1x RS2321x RS4851x Micro USB 2.02x SIM card slots128 MB internal Flash memory170 mAh Li-Ion battery 3.7 V (0.63 Wh)Wireless networksLTE(CaT1)2G(GSM/GPRS)GNSSBluetooth 4.0 + LESensorsAccelerometerFMC225 is WATER and DUST resistant real-time tracking terminal with GNSS and LTE/GSM connectivity and backup battery. FMC225 features RS485/RS232 data interface, which gives ability to connect various third-party external devices. It is perfectly suitable for applications where location acquirement of remote objects is needed:fleet managementcar rental companiestaxi companiespublic transportlogistics companiespersonal carsand so on. Because of IP67 casing, device is totally protected from dust and remains safe during the short periods of immersion in water up to 1m depth. As a result, FMC225 can be used in agriculture, construction and mining or any other fleet where harsh tracking conditions exists.

The ADM691A/ADM693A/ADM800L/ADM800M family of supervisory circuits offers complete single chip solutions for power supply monitoring and battery control functions in microprocessor systems. These functions include µP reset, backup-battery switchover, watchdog timer, CMOS RAM write protection, and power-failure warning. The family of products provides an upgrade for the MAX691A/93A/800M family of products.

FMM130 Advanced CAT M1 / GSM / GNSS / BLE Terminal with Internal Antennas and Backup battery3x Digital Input3x Digital Output2x Analog Input1x CAN Adapter Input1x 1-wire1x Micro USB 2.01x Micro SIM slot128 MB internal flash memoryWireless BandsLTE CAT M1NB-IoTGSMGPRSGNSSBluetoothFMM130 is small and professional real-time tracking terminal with GNSS and LTE CAT-M1/NB-IoT/GSM connectivity and backup battery. Device equipped with GNSS/Bluetooth and LTE CAT-M1/NB-IoT modules with fallback to 2G network, internal GNSS and LTE antennas, configurable digital, analogue inputs and digital outputs, negative input, impulse inputs. It is perfectly suitable for applications where location acquirement of remote objects is needed: fleet managementcar rental companiestaxi companiespublic transportlogistics companiespersonal cars and so on.Device supports both LTE M1 and NB IoT connectivityConfigurable DIN/AIN for flexible remote monitoring and control.CAN data reading from vehicles and specialized transportAllows device to work without external power sourceNegative input will allow easier installation of accessoriesImpulse inputs for fuel flow meters data readingUse CasesLight vehiclesHeavy duty transportTrailer TrackingRefrigerated transportInternational logisticsCarsharing

For protection of electrical equipment and switches• Non-conductive• Radio Free• Key can be removed only in the closed state of the lockComes with a 6 'DANGER' (danger) stickers in different colors, white and 'Property of' (the property of) stickers(Supplied without hasp)

FMB910 Smart Tracker with internal Backup battery1x Digital Inputs1x Digital Outputs1x Analog Inputs1x Micro USB 2.01x Micro SIM slot128 MB internal flash memory170 mAh Li-Ion battery (0.63 Wh)Wireless bandsGSMGPRSGNSSBluetoothTeltonika FMB910 is a reliable track & trace tracker for:motorbikeslight and heavy vehicles in applications like delivery transportrental carsrecovery of stolen carspublic safety servicesand much moreTracker is equipped with internal High Gain GNSS and GSM antennas and integrated backup battery.Input/output extend device usage scenarios:Digital input can be used for ignition, door or alarm button status monitoringAnalog input allows to monitor external devices/sensors, including fuel sensorsDigital output enables vehicle remote immobilizingFMB910 is EASY tracker with simplified management to fulfill the demands of track&trace.

FMC640 Professional LTE/GNSS Terminal4x Digital input4x Digital Output4x Analog Input1x 1-wire1x RS2321x RS4852x CAN J19391x CAN J17081x K-Line1x Micro USB 2.02x SIM Card slot1x Micro SD Card slot2 MB internal flash memoryWireless bandsLTE(CaT1)3G(UMTS/HSPA)2G(GSM/GPRS)GNSSBluetooth 5.0 + LETeltonika FMC640 is a PROFESSIONAL series device with 4G (LTE Cat 1) network coverage including 3G (UMTS), 2G (GSM) fallback compatibility. Device equipped with GNSS and LTE modules, external GNSS and LTE antennas. FMC640 will maximize your fleet efficiency with features like FMS CAN data (J1939), fuel CAN data (J1708), tachograph live data (K-Line), remote tachograph file download, various third party RS232 or RS485 devices support and Dual-SIM.Terminal is suitable for applications like international logistics, refrigerated transport, agriculture, construction & mining, security & emergency services and even more.Reliable 4G connection with fallback to 3G and 2G networkBluetooth for external devices and sensorsCAN data reading from vehicles and specialized transportDual SIM - significantly reduce roaming costsRS232/RS485 serial communication interfacesTachograph files and data remote downloadUse CasesConstruction & MiningHeavy Duty TransportPublic Safety ServicesRefrigerated TransportInternational LogisticsAgriculture Transport

APC Easy UPS BVX 1600VA, 230V, AVR, IEC SocketsThe APC by Schneider Electric Easy UPS offers power and surge protection for wireless networks, computers, gaming consoles and other electronics in your home or business. This UPS supply battery backup during outages and unstable voltage fluctuations, as well as provide protection from damaging surges and spikes. They are the choice helps to protect your data and keep you connected.Input:1x IEC C13220 - 240 V ACOutput:6x IEC C14 230 V AC1600 VA / 900 WAutomatic Voltage Regulation (AVR)Automatic Voltage Regulation boosts/trims the AC voltage when it drops/exceeds levels.This allows the equipment plugged into the unit to operate during low/high voltage conditions, conserving the battery power in the event of a power cut.The Easy UPS will switch to battery power if the input voltage level becomes too low/high for the Automatic Voltage Regulation to compensate, or if the AC power is distorted.Quick MuteThe Easy UPS is able to temporarily mute user correctable audible alarms such as On Battery. During such audible alarms, a short press (less than 2 seconds) of the POWER button will temporarily mute the audible alarm until the condition has been reset. A short double beep will confirm that Quick Mute has been activated. Pressing the POWER button for more than 2 seconds will turn off the UPS.Other events such as Battery replacement and Charger notification can not be temporarily muted. The unit in these cases must be turned off.

APC EASY UPS BV 800VA, AVR, IEC Outlet, 230VBest Value UPS with Battery Backup & Surge Protection for Electronics and ComputersOutputOutput power capacity: 450Watts / 800VAMax Configurable Power (Watts): 450Watts / 800VANominal Output Voltage: 230VOutput Frequency (not synced): 50/60 Hz +/-1 HzTopology: Line InteractiveWaveform type: Stepped approximation to a sinewaveOutput Connections: (6) IEC 320 C13 (Battery Backup)Transfer Time: 6ms typical : 10ms maximumInputNominal Input Voltage: 230VInput frequency: 50/60 Hz +/- 5 Hz (auto sensing)Input Connections: IEC-320 C14Cord Length: 5ft (1.52meters)Number of Power Cords: 1 Automatic Voltage Regulation (AVR) Automatically steps up low voltage and steps down high voltage to levels that are suitable for your equipment. Wall-mount holes Allow flexibility for setup in tight locations and mounting on wall or other surfaces.Sleek designSlim, modern design can be upright, flat, or wall-mounted to comfortably fit any electronics set-up and complement home décor.Transformer-block spaced outletsProtect equipment with input transformer blocks without blocking access to other receptacles.Cold-start capableProvides temporary battery power when the utility power is out.Boost Automatic Voltage Regulation (AVR)Preserves battery life and maximizes runtime by correcting low voltages without discharging the battery.Battery failure notificationProvides early-warning fault analysis on batteries enabling timely preventive maintenanceAdvanced Safety FeaturesSafeguard your Home UPS from overloads, excessive mains voltages, short circuits, installation mishaps and battery damage due to low voltage situations.Intelligent battery managementMaximizes battery performance, life, and reliability through intelligent, precision charging.Safety-agency approvedEnsures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.LED IndicatorsProvide easy-to-read status of the unit and utility power conditions.Audible alarmsProvides notification of changing utility power and UPS power conditionsBattery and surge protected outletsBack up and protect your hardware and data during power outages, surges and spikes.Battery backup and surge protectionOutlets provide abundant runtime for network gateway equipment and other critical low-power devices, allowing for hours of internet access during a power...

edding 8400 CD/DVD/BD markers, set of 4Whether in offices for data backups or at home for personal archives, this marker can be easily used on CDs and other media. The soft tip and pigment ink permanently mark without damaging the surface, which can make the data unrecognisable. The water-based ink is solvent-free and, in combination with the soft tip, ensures your data stays as safe as possible. The set contains four markers in different colours.The ideal marker for labelling CDs, DVDs and Blu-raysPermanent ink for durable and waterproof markings on CDs, DVDs and Blu-raysSoft and flexible tips do not damage the surface, ensuring maximum data security

APC Easy UPS BVX 2200VA, 230V, AVR, IEC SocketsThe APC by Schneider Electric Easy UPS offers power and surge protection for wireless networks, computers, gaming consoles and other electronics in your home or business. This UPS supply battery backup during outages and unstable voltage fluctuations, as well as provide protection from damaging surges and spikes. They are the choice helps to protect your data and keep you connected.Input:1x IEC C20220 - 240 V ACOutput:6x IEC C14 230 V AC2200 VA / 1200 WAutomatic Voltage Regulation (AVR)Automatic Voltage Regulation boosts/trims the AC voltage when it drops/exceeds levels.This allows the equipment plugged into the unit to operate during low/high voltage conditions, conserving the battery power in the event of a power cut.The Easy UPS will switch to battery power if the input voltage level becomes too low/high for the Automatic Voltage Regulation to compensate, or if the AC power is distorted.Quick MuteThe Easy UPS is able to temporarily mute user correctable audible alarms such as On Battery. During such audible alarms, a short press (less than 2 seconds) of the POWER button will temporarily mute the audible alarm until the condition has been reset. A short double beep will confirm that Quick Mute has been activated. Pressing the POWER button for more than 2 seconds will turn off the UPS.Other events such as Battery replacement and Charger notification can not be temporarily muted. The unit in these cases must be turned off.

APC EASY UPS BV 800VA, AVR, Schutzkontakt Outlet, 230VBest Value UPS with Battery Backup & Surge Protection for Electronics and ComputersOutputOutput power capacity: 450Watts / 800VAMax Configurable Power (Watts): 450Watts / 800VANominal Output Voltage: 230VOutput Frequency (not synced): 50/60 Hz +/-1 HzTopology: Line InteractiveWaveform type: Stepped approximation to a sinewaveOutput Connections: (4) Schutzkontakt CEE 7 (Battery Backup)Transfer Time: 6ms typical / 10ms maximumInputNominal Input Voltage: 230VInput frequency: 50/60 Hz +/- 5 Hz (auto sensing)Input Connections: Schutzkontakt CEE 7/7PCord Length: 5ft (1.52meters)Number of Power Cords: 1 Automatic Voltage Regulation (AVR) Automatically steps up low voltage and steps down high voltage to levels that are suitable for your equipment. Wall-mount holes Allow flexibility for setup in tight locations and mounting on wall or other surfaces.Sleek designSlim, modern design can be upright, flat, or wall-mounted to comfortably fit any electronics set-up and complement home décor.Transformer-block spaced outletsProtect equipment with input transformer blocks without blocking access to other receptacles.Cold-start capableProvides temporary battery power when the utility power is out.Boost Automatic Voltage Regulation (AVR)Preserves battery life and maximizes runtime by correcting low voltages without discharging the battery.Battery failure notificationProvides early-warning fault analysis on batteries enabling timely preventive maintenanceAdvanced Safety FeaturesSafeguard your Home UPS from overloads, excessive mains voltages, short circuits, installation mishaps and battery damage due to low voltage situations.Intelligent battery managementMaximizes battery performance, life, and reliability through intelligent, precision charging.Safety-agency approvedEnsures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.LED IndicatorsProvide easy-to-read status of the unit and utility power conditions.Audible alarmsProvides notification of changing utility power and UPS power conditionsBattery and surge protected outletsBack up and protect your hardware and data during power outages, surges and spikes.Battery backup and surge protectionOutlets provide abundant runtime for network gateway equipment and other critical low-power devices, allowing for...

APC Easy UPS BVX 1200VA, 230V, AVR, Earthed SocketsThe APC by Schneider Electric Easy UPS offers power and surge protection for wireless networks, computers, gaming consoles and other electronics in your home or business. This UPS supply battery backup during outages and unstable voltage fluctuations, as well as provide protection from damaging surges and spikes. They are the choice helps to protect your data and keep you connected.Input:1x Power cord220 - 240 V ACOutput:4x Earthed socket outlet 230 V AC1200 VA / 650 WAutomatic Voltage Regulation (AVR)Automatic Voltage Regulation boosts/trims the AC voltage when it drops/exceeds levels.This allows the equipment plugged into the unit to operate during low/high voltage conditions, conserving the battery power in the event of a power cut.The Easy UPS will switch to battery power if the input voltage level becomes too low/high for the Automatic Voltage Regulation to compensate, or if the AC power is distorted.Quick MuteThe Easy UPS is able to temporarily mute user correctable audible alarms such as On Battery. During such audible alarms, a short press (less than 2 seconds) of the POWER button will temporarily mute the audible alarm until the condition has been reset. A short double beep will confirm that Quick Mute has been activated. Pressing the POWER button for more than 2 seconds will turn off the UPS.Other events such as Battery replacement and Charger notification can not be temporarily muted. The unit in these cases must be turned off.

APC EASY UPS BV 1000VA, AVR, IEC Outlet, 230VBest Value UPS with Battery Backup & Surge Protection for Electronics and ComputersOutputOutput power capacity: 600Watts / 1.0kVAMax Configurable Power (Watts): 600Watts / 1.0kVANominal Output Voltage: 230VOutput Frequency (not synced): 50/60 Hz +/-1 HzTopology: Line InteractiveWaveform type: Stepped approximation to a sinewaveOutput Connections: (6) IEC 320 C13 (Battery Backup)Transfer Time: 6ms typical : 10ms maximumInputNominal Input Voltage: 230VInput frequency: 50/60 Hz +/- 5 Hz (auto sensing)Input Connections: IEC-320 C14Cord Length: 5ft (1.52meters)Number of Power Cords: 1 Automatic Voltage Regulation (AVR) Automatically steps up low voltage and steps down high voltage to levels that are suitable for your equipment. Wall-mount holes Allow flexibility for setup in tight locations and mounting on wall or other surfaces.Sleek designSlim, modern design can be upright, flat, or wall-mounted to comfortably fit any electronics set-up and complement home décor.Transformer-block spaced outletsProtect equipment with input transformer blocks without blocking access to other receptacles.Cold-start capableProvides temporary battery power when the utility power is out.Boost Automatic Voltage Regulation (AVR)Preserves battery life and maximizes runtime by correcting low voltages without discharging the battery.Battery failure notificationProvides early-warning fault analysis on batteries enabling timely preventive maintenanceAdvanced Safety FeaturesSafeguard your Home UPS from overloads, excessive mains voltages, short circuits, installation mishaps and battery damage due to low voltage situations.Intelligent battery managementMaximizes battery performance, life, and reliability through intelligent, precision charging.Safety-agency approvedEnsures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.LED IndicatorsProvide easy-to-read status of the unit and utility power conditions.Audible alarmsProvides notification of changing utility power and UPS power conditionsBattery and surge protected outletsBack up and protect your hardware and data during power outages, surges and spikes.Battery backup and surge protectionOutlets provide abundant runtime for network gateway equipment and other critical low-power devices, allowing for hours of internet access during a power...

APC Easy UPS BVX 900VA, 230V, AVR, IEC SocketsThe APC by Schneider Electric Easy UPS offers power and surge protection for wireless networks, computers, gaming consoles and other electronics in your home or business. This UPS supply battery backup during outages and unstable voltage fluctuations, as well as provide protection from damaging surges and spikes. They are the choice helps to protect your data and keep you connected.Input:1x IEC C14220 - 240 V ACOutput:4x IEC C13 230 V AC900 VA / 480 WAutomatic Voltage Regulation (AVR)Automatic Voltage Regulation boosts/trims the AC voltage when it drops/exceeds levels.This allows the equipment plugged into the unit to operate during low/high voltage conditions, conserving the battery power in the event of a power cut.The Easy UPS will switch to battery power if the input voltage level becomes too low/high for the Automatic Voltage Regulation to compensate, or if the AC power is distorted.Quick MuteThe Easy UPS is able to temporarily mute user correctable audible alarms such as On Battery. During such audible alarms, a short press (less than 2 seconds) of the POWER button will temporarily mute the audible alarm until the condition has been reset. A short double beep will confirm that Quick Mute has been activated. Pressing the POWER button for more than 2 seconds will turn off the UPS.Other events such as Battery replacement and Charger notification can not be temporarily muted. The unit in these cases must be turned off.

5-bay 3.5”/2.5” SATA expansionEasily add 5 additional drive bays to Synology DiskStation1. Supporting both 2.5” and 3.5” SATA drives, DX517 is a flexible solution supporting on-the-fly volume expansion or serving as a local backup destination.Online volume expansionManaged from DiskStation Manager on the host NAS, the additional bays in the DX517 are immediately ready to be used once connected. On-the-fly volume expansion ensures that storage and services on the host are not interrupted during volume expansion.Hot-swappable drive tray designThe hot-swappable drive trays of DX517 allow easy drive installation and replacement without powering down the system. Screwless drive tray design reduces the time needed for system setup.Dedicated local backup solutionSynology DX517 can be used as a dedicated local backup solution for the Synology DiskStation. When created as a separate volume, the DX517 provides a great backup solution to its local hard disks in case of system failure.

APC Easy UPS BVX 1200VA, 230V, AVR, IEC SocketsThe APC by Schneider Electric Easy UPS offers power and surge protection for wireless networks, computers, gaming consoles and other electronics in your home or business. This UPS supply battery backup during outages and unstable voltage fluctuations, as well as provide protection from damaging surges and spikes. They are the choice helps to protect your data and keep you connected.Input:1x IEC C14220 - 240 V ACOutput:6x IEC C13 230 V AC1200 VA / 650 WAutomatic Voltage Regulation (AVR)Automatic Voltage Regulation boosts/trims the AC voltage when it drops/exceeds levels.This allows the equipment plugged into the unit to operate during low/high voltage conditions, conserving the battery power in the event of a power cut.The Easy UPS will switch to battery power if the input voltage level becomes too low/high for the Automatic Voltage Regulation to compensate, or if the AC power is distorted.Quick MuteThe Easy UPS is able to temporarily mute user correctable audible alarms such as On Battery. During such audible alarms, a short press (less than 2 seconds) of the POWER button will temporarily mute the audible alarm until the condition has been reset. A short double beep will confirm that Quick Mute has been activated. Pressing the POWER button for more than 2 seconds will turn off the UPS.Other events such as Battery replacement and Charger notification can not be temporarily muted. The unit in these cases must be turned off.